When a key snaps off in a lock, the most useful thing you can do is stop. Don't poke at the piece, don't try to turn the lock with the half still in your hand, and don't try a glue trick you saw online. Most broken keys come out cleanly with the right tools, and the lock keeps working, but only if the fragment is still sitting near the front of the keyway. Keep both pieces, figure out whether the door is secure, and then call for broken key extraction. Below are the mistakes that turn a small job into a bigger one, and how to handle the time until the key is out.
The five things that make it worse
Every one of these feels reasonable in the moment. Here's what each one tends to do inside the lock:
- Pushing the piece back in with the other half. People do this to line the two halves up and turn the lock. It drives the fragment deeper, past the point where an extraction tool can easily catch it.
- Super glue on the end of the broken half. Glue runs. If it reaches the pins or the side of the keyway, the fragment is now stuck to the lock, and a job that needed a thin hook may now need the cylinder taken out.
- Tweezers, bobby pins and paper clips. The fragment fits the keyway tightly, so there's rarely room for a household tool beside it. What usually happens is the tip pushes the piece further in, or a bit of the pin snaps off and joins it.
- Spraying oil into the keyway. Oil doesn't loosen a key, because the key isn't rusted in place. It's held by the pins and the tight fit. Household oil also collects dust and gums up in the cold, which leaves you with a second problem in January.
- Drilling. Drilling destroys the cylinder and is almost never the first step for a broken key. Leave it for the rare case when nothing else works.
There's one small exception to "leave it alone." If a good length of key is sticking out and you can hold it with your fingertips, one gentle, straight pull is fine. If it doesn't slide right out, stop there. Pliers tend to chew up the soft brass and shorten what's left to grab.
First question: is the door open or closed?
The next steps depend on which side of the door you're on.
You're outside and the door is locked
This is a lockout with an extra step. Check for another way in that doesn't involve force, like a side door or a door from the garage. Many Hudson ranches and capes have a second entrance that nobody thinks about until they need it. The article on getting locked out after dark walks through that search in order, including what to do if you're stuck outside in the cold. If a young child or someone who needs help is inside, or a pet is in distress, call 911 first.
You're inside, or the door is unlocked
Then you have some breathing room. Leave the door unlocked until the key is out, unless you've confirmed you can get back in another way. If you need to secure the house while you wait, try the inside thumb turn gently. If it moves freely, you can lock up from inside and stay put, or leave through another door you have a key for. If the thumb turn resists, don't force it, because the key may have snapped partway through a turn and left parts inside out of position.
The door is at a business
If this happens at closing on Lowell Road or Route 102, don't leave the building unsecured. Keep someone at the door until the lock works again, and let the owner or manager know. If you have another entrance and a key for it, tell us which door people need to use, so we can plan around your opening time. Commercial locks have their own quirks, so mention whether it's a storefront cylinder, a lever lock or a key in a panic bar.
What to tell the locksmith when you call
A few details help us bring the right tools and give you a straight answer on the phone:
- Which lock it is. Front door deadbolt, knob, padlock, mailbox, file cabinet or car door. A small cabinet lock is a different job from a thick deadbolt.
- What the key was doing when it broke. Was it going in, turning, or coming out? A key that broke mid-turn often leaves the inner cylinder rotated out of its resting position, and that changes how it has to be removed.
- Whether anyone has tried to get it out. If you did push on it or try glue, please say so. It's no problem, and it helps us arrive prepared.
- Whether the door is locked and who needs to be inside. We'll also confirm you live there or own the property before opening anything.
- Whether you have both pieces. A clear photo of the lock and the broken half helps too.
How it usually gets resolved
Before anything happens, you'll hear what the job involves and the total. From there, the technician slides a thin tool alongside the fragment, catches the cuts and draws it out. If it won't come that way, the cylinder can usually be taken out and the piece pushed out from behind. Once the key is out, we can cut a new one, often from your two pieces, and test it in the lock with the door open and closed. If the old key was worn, we'd rather cut the new key to the lock than copy the wear.
Then we look at why it broke. A key rarely snaps for no reason, and a new key in a binding lock is just the next broken key waiting to happen. A worn cylinder may need cleaning, a rekey or a new lock. If you've recently moved in, our list of what to do about the locks in your first week covers when a rekey makes sense anyway.
Why this happens more once it gets cold
We hear about snapped keys more as the mornings get colder in southern New Hampshire, and there's a simple reason. A door that fit fine in September can shift as the house and frame move with the seasons, so the bolt starts dragging against the strike. People compensate by twisting harder, and a brass key can only take so much. Older doors and doors that take direct weather tend to feel it first.
Your key will usually warn you first. Take it seriously if:
- The lock only turns when you pull or lift the door.
- You've straightened a bent key by hand, even once.
- You can see a hairline crack near the shoulder, where the blade meets the head.
- The key is a copy of a copy and needs some wiggling to go in.
- You use the key as a handle to pull the door shut.
If any of those sound familiar, having a fresh key cut and the door adjusted now is a much easier afternoon than a snapped key on a freezing morning. If you're in the Hudson area, see our Hudson locksmith page, and we answer 24/7 if it's already happened.
Can I use the lock while the broken piece is inside?
It's better not to. Even if a thumb turn still moves from the inside, a spare key can't go in from the outside, and forcing anything can push the fragment deeper. Treat the lock as out of service until the piece is out.
Does a broken key mean I need a new lock?
Usually not. Most fragments come out without harming the lock, and it works normally with a new key. We'll tell you if the cylinder is worn enough that replacing it makes more sense.
What if my key broke in the car instead?
The same rule applies: leave it alone and don't try to start or turn anything with the remaining piece. An ignition or a car door lock can also be handled on site. See our ignition repair page.

